Startechcom SV1115IPEXT Manual do Utilizador

IP KVM Switch1-Port USB PS/2 Server Remote Control IP KVM with Virtual Media and SerialSV1115IPEXTInstruction Manual

6complete step 11 now and continue to the section entitled Configuring SV1115IPEXT.Connect the power cord (provided) to an appropriate electrical 10. o

7“console” connectors on a KVM switch allowing you to control more than one computer remotely using a single Server Remote Control. If you want to use

8Make sure the Pointer speed bar is centered and Acceleration is set 3. to None. Windows 2000From the Control Panel, Click on Mouse.1. From Mouse prop

9Upon boot-up, including following a reset, SV1115IPEXT will display a window on the local video output (front VGA connector), that will appear as fol

10Web Conguration Using DHCPThis method requires that your network implement DHCP (Dynamic Host Configuration Protocol), usually on a server or networ

11and wish to proceed with the Web configuration, do not power off the unit or your DHCP server, since the Server Remote Control might lease a differen

12Administrator for assistance.NOTE: It is advisable to verify whether another device on your network is using the same IP address as the SV1115IPEXT

13if connecting to the DCE Serial port, female if connecting to the DTE Serial port) to the SV1115IPEXT. Configure the terminal software with “8N1” set

14Using the Web InterfaceThe Web interface is the most intuitive way to configure the SV1115IPEXT. Offering a Java-based VNC client that can be used to

15Web Interface IntroductionAfter the initial login screen, the screen will be divided into several sections, four of which will remain on the screen

FCC Compliance StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

16NOTE: While these four sections remain stationary, depending on your selections, the center of the page will display the desired content.Main Menu s

17at the drive, it will notice the changes. You can read files from the virtual disk at any time, as long as the host is not actively writing to the di

18easily drag and drop files up to 8MB in size to this device. In Windows Explorer, you can choose the Eject option to make the data available to remot

19file system) but any disk image may be used.Web server must support “byte ranges”. Persistent connections are •used, if available, as this greatly i

20The Admin functions allow you to access all of the features you will need to perform an initial configuration of the SV1115IPEXT.Dynamic Host Configur

21Domain Name Server (optional)This section allows you to specify DNS servers and the default DNS domain suffix in use on the network. If DHCP is enabl

22may not be separately configured. Using DHCP with Bridging increases boot time, because the 802.1d (STP) algorithm must finish before the DHCP broadca

23defined value that identifies the controlled machine on the network. The official DNS name of the controlled machine is a obvious value to put here, bu

24Remember to enable RADIUS after configuring it. While RADIUS authentication is enabled, the locally defined accounts on the Server Remote Control unit

25The firmware on the Server Remote Control is field upgradable. To upgrade to another version, login as admin. Auto Self UpgradeThe SV1115IPEXT unit in

iTable of ContentsIntroduction ... 1Packaging Contents...

26Purchase OptionsCertain firmware features may be offered separately from the base unit, in order to reduce the initial cost for the Server Remote Con

27Site map MenuThis menu provides a hyperlinked directory of each setting available on the Web configurator.Copyright MenuProvides the Terms of Use and

28If you changed the status of the Ethernet Bridging feature, you will also need to power the SV1115IPEXT on and off again to enable your changes.Acce

29This client software requires the use of Java 2 (JRE 1.4) to enable features like wheel mouse support. Sun Microsystems’ Java site, www.java.com, is

30connection will be terminated.The port number “15900” is arbitrary in the above example and can •be any number (1025...65535). It is the port numbe

31Bribar FeatureAlong the bottom of the VNC screen is a dark blue bar with various buttons known as the bribar. Its purpose is to show a number of cri

32Keys: Shows the VirtKeys menu, which allows you to simulate pressing special keys such as the Windows key or complex multi-key sequences.Disk: Shows

33Main MenuTo access the main menu, quickly press F7 twice quickly. You must press the key twice within one second. If you press it once or too slowly

34time spent on compression versus more bandwidth. There is no visual difference between the modes, but there can be a noticeable difference in speed

35Bribar:• Closes or reopens the Bribar window along the bottom of the screen.VirtKeys MenuClicking any button in the top half of the window simulat

iiBribar Feature ...31Main Menu ...

36Video Tuning MenuUse the Auto Everything button to automatically fine-tune all three adjustments. If the test pattern for Color Offset calibration is

37to perform this operation in 24-bit or 32-bit color video mode (i.e. True Color). Although the algorithm may work in 16-bit or 8-bit color video mod

38Some external KVM switches generate video noise as well. Try to •keep cables short, in order to reduce this effect.Enable the Noise Filter option (

39video properties, you can use this menu to exercise a great deal of control over the settings if you wish.The Presets section contains up to sixteen

40to a medium grey color. All blocks that are sent from that point on will show up on the screen as they are sent. Click the button again to reset the

41standard. To determine if your computer supports this IPMI, consult its documentation for more information.IPMI is used to configure and control a de

42the DTE Serial port) to the SV1115IPEXT.Conguring IPMI on the SV1115IPEXTOnce you have connected the IPMI-configured serial port to the SV1115IPEXT

43Enable IPMI (Intelligent Platform Management Interface via serial •port: select Enabled.Select which serial port to use: select either Front serial

44implementations vary widely across manufacturers, the information you are able to see on your status screen may differ from the examples. Note that

45Reset: Equivalent to pressing the RESET button on the managed computer. (The computer will restart.)ON/OFF: Powers the host computer on or off depen

1IntroductionPackaging Contents1 x SV1115IPEXT unit•1 x Power Adapter•1 x Power Cord•1 x Instruction Manual•1 x PS/2 KVM cable•System Requirement

46Connecting a ModemThe SV1115IPEXT will work with virtually any Hayes-compatible modem that recognizes the standard AT command set. Some modem manufa

47Place the modem near the SV1115IPEXT and an available telephone jack. Connect the modem to the telephone jack, data cable, and power source accordin

48connection speed for greater stability (and so on). You may wish to test the connection with the default init string first, before making changes spe

49Click Next.13. You may select to add a shortcut to the desktop for this connection. 14. Click Finish.PPP (Point-to-Point Protocol) must be used; no

50active, their screens will be in gray scale as well. When PPP in inactive, color is automatically re-enabled.Some areas of the screen may not be upd

51Troubleshooting GuideThe following messages will appear in the system log on the Status screen in the Web interface and may help to diagnose problem

52Serial Remote Control operationBackgroundThe SV1115IPEXT offers a unique way to expand the functionality of the base product. Using the integrated R

53admin. Other users will be able to view which modules are active but cannot configure them.Once you are logged in, choose the Admin/Setup option from

54log. Note that existing data is overwritten automatically when the 200 character limit is reached.IPMI: Shows the IPMI command interface for the dev

55L – Low log entries (line buffer)1 – Show last 10 log entriesother – Return to connectionPress key ->To execute the desired command, simply press

2Required Cables and HardwareThe included integrated KVM cable will allow you to connect the SV1115IPEXT to most IBM compatible computers. Depending o

56stty –crtscts < /dev/[serial port]A maximum of four users may simultaneously login to the same •module. All users may type commands at any time,

57any way, nor does it make the SV1115IPEXT any more vulnerable to outside attacks.Can I prevent the warning from occurring?Yes. You have two options

58Remote mouse and local mouse don’t line up.Use the Mouse resync command in the main menu or press the Resync button on the Bribar. If the mouse poin

59configuration.Mouse performance is erratic when using the GNOME or KDE desktop in a Linux X-Window environment.The mouse controls in GNOME and KDE en

60Supported ProtocolsService Description BenefitSSH Secure Shell May be used to securely “tunnel” VNC and HTTP protocols.HTTP Web redirector (to HTTPS)

61SpecicationsConsole Connectors (Local)2 x PS/2 female1 x DE-15 VGA female3 x USB type A2 x RJ45 (WAN/LAN)2 x DB9 serial (female/male)1 x R-Port2 x

62Technical SupportStarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions.

StarTech.com has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans m

3InstallationConnecting to the Host Computer and NetworkFollow these instructions if the host computer uses a PS/2 keyboard and mouse:Power down the c

4the male VGA (monitor) connector and connect it to the VGA-out connector on the back of the host computer.Connect the PS/2 keyboard and mouse connect

5Follow these instructions if the host computer uses a USB keyboard and mouse:IMPORTANT: Not all computers fully support USB mice and keyboards and re